Recent content by frenchfry

The answer is: You don't do it! Switch to bar charts or use another application which can display bar charts. Regarding gaps... either: - Use applications like Ninjatrader, Sierra Charts, etc. which can create a de-gapped chart or display de-gapped bars as indicators. - Later in the evolution...

Sure. I think the first time I noticed his "new approach" after "Exact Science" was in the thread "Why is the obvious not so obvious". However I don't remember anymore why I didn't put it in my attached list. The challenge could be that some attachments are no longer accessible. Maybe the...

The lateral is maybe not a good example for a Squish. If you have a two bar combination then those two bars can be "squished" into one synthetic bar which in your FTP example gets the open, high and low from the first bar and the close from the second bar. The volume will be taken from which...

P1 For band A, P1 is coincident with the trend ending bar. for all failsafe (two contexts) a P1 is coincident with the trend ending bar. For all other contexts, P1 is assigned to the first non suppressed bar available. ………………………. The P1 begins all trends (all four types). …………………….. P1 is...

6 Steps to name volume bars you are using the 6 steps illustration (past post) to wrap up gaining facility on taking the full offer of the market. Write a text for using the 6 steps. a. You assign P1. b. You compare forming bar to prior elligible bar. (see MADA Flow Sheet and the Mathemtics...

Volume test procedure (by JH) a three part OOE is used to test volume to obtain the bar volume name. This has to be done precisely and exactly as stated here. when permission is given and suppression is lifted (this is a comment to coders), then the following tests are preformed. 1. test for...

Again... everything is too long ago. Still need to refresh my memory. As a side note I would also suggest what deb_sezwhat suggested: Ignore Spyder. If you want to learn Spyder's way read Spyder's posts. If you want to learn Jack's way before "Exact Science" read Jack's old posts. If you...

Rev Chron... It's a long time ago. If I remember it correctly then it simply means this: In your log you have the column for P1 - T1 - P2 - T2P - etc. Let's say for your previous volume bar you logged a T1. The new bar arrives and you have permission to measure. The next column in your log...

Sorry again... because Hero is using a slightly different terminology than Jack did, in this thread I don't know if this ITZ is something important or not. What I see... and what I remember from Jack... is that there is a container. Call that container whatever you want. In this container at...

Don't know about all this BBT and equal weight stuff but if the lines are drawn a little bit different then the ftt or FTT is clearly visible. If there is a VE the lines have to be accelerated.

Pity! At the beginning I only saw his longwinded posts and immediately skipped to the next post. I found his posts horrible... a waste of time. That perception changed when I finally decided to "fight" my way through what he was writing, trying to understand it line by line. At the end more...

Sorry I didn't follow this thread from the beginning therefore I hope somebody else can take over. But I think the key in understanding this drill is the successful completion of the previous drill with the "bar legs". This together with what Jack calls "synthetic bar" should put you on the...

This looks good. The only thing I found was your first blue highlight where you call that bar formation a FBP before it becomes an OB. That looks more like a Stich. Once you have bar 3 of a lateral it will be labeled Lat3, next bar Lat4, next bar Lat5, etc. In fact... usually (that's what Jack...

Btw TickingAway...after you switched to bar charts and are able to identify the cases correctly based on highs and lows, then move to the next step and read (search for "degap" or "degaping") what Jack says about intra bar gaps and redo your bar assignments. This is where you focus also on the...

If you have bar two, then at that moment in time you don't have a lateral, yet. And you don't know yet if bar three will create a lateral or something else. So you do what the volume test procedure tells you to do. Which is...?